# traceroute www.google.com -bash: traceroute: command not found
Or you can verify the traceroute install or not by issue which command :
# which traceroute /usr/bin/which: no traceroute in (/usr/local/sbin:/usr/local/bin:/sbin:/bin:/usr/sbin:/usr/bin:/root/bin)
2. Để cài đặt traceroute, hãy chạy lệnh sau:
# yum install traceroute -y
3. Xác minh cài đặt lệnh hay không:
# which traceroute /bin/traceroute
4. Cách sử dụng lệnh traceroute:
a. Tìm đường dẫn mạng từ máy chủ centos 7 của tôi đến google.com:
# traceroute [options]
Ví dụ:
# traceroute www.google.com traceroute to www.google.com (58.27.108.153), 30 hops max, 60 byte packets 1 192.168.2.1 (192.168.2.1) 9.233 ms 9.020 ms 8.857 ms 2 219.93.218.177 (219.93.218.177) 20.717 ms 20.529 ms 27.526 ms 3 60.49.55.93 (60.49.55.93) 57.368 ms 57.446 ms 57.187 ms 4 10.55.32.58 (10.55.32.58) 76.846 ms 10.55.32.56 (10.55.32.56) 66.418 ms 66.906 ms 5 58.27.105.125 (58.27.105.125) 75.779 ms 65.556 ms 65.592 ms 6 * * * 7 * * * 8 * * * 9 * * * 10 * * * 11 * * * 12 * * * 13 * * * 14 * * * 15 * * * 16 * * * 17 * * * 18 * * * 19 * * * 20 * * * 21 * * * 22 * * * 23 * * * 24 * * * 25 * * * 26 * * * 27 * * * 28 * * * 29 * * * 30 * * *
1 là cổng internet trên mạng mà quá trình theo dõi này đã được thực hiện (IP cục bộ của modem ADSL)
2 là ISP mà máy tính gốc được kết nối.
Chi tiết IP WAN modem PPPoE của tôi:
b. Tìm đường dẫn mạng từ máy chủ centos 7 của tôi đến google.com và không phân giải địa chỉ IP thành tên miền của chúng:
# traceroute www.google.com -n
c. Tìm đường dẫn mạng từ máy chủ centos6 của tôi đến google.com và đặt số giây để đợi phản hồi cho một đầu dò là 0,1 giây (Mặc định là 5,0):
# traceroute www.google.com -w 0.1
d. Tìm đường dẫn mạng từ máy chủ centos6 của tôi đến google.com và đặt số lượng đầu dò cho mỗi bước là 5 (Mặc định là 3):
# traceroute www.google.com -q 5
5. Hiển thị các tùy chọn dòng lệnh cơ bản trợ giúp để sử dụng nhiều hơn:
# traceroute --help Usage: traceroute [ -46dFITnreAUV ] [ -f first_ttl ] [ -g gate,... ] [ -i device ] [ -m max_ttl ] [ -N squeries ] [ -p port ] [ -t tos ] [ -l flow_label ] [ -w waittime ] [ -q nqueries ] [ -s src_addr ] [ -z sendwait ] host [ packetlen ] Options: -4 Use IPv4 -6 Use IPv6 -d --debug Enable socket level debugging -F --dont-fragment Do not fragment packets -f first_ttl --first=first_ttl Start from the first_ttl hop (instead from 1) -g gate,... --gateway=gate,... Route packets through the specified gateway (maximum 8 for IPv4 and 127 for IPv6) -I --icmp Use ICMP ECHO for tracerouting -T --tcp Use TCP SYN for tracerouting -i device --interface=device Specify a network interface to operate with -m max_ttl --max-hops=max_ttl Set the max number of hops (max TTL to be reached). Default is 30 -N squeries --sim-queries=squeries Set the number of probes to be tried simultaneously (default is 16) -n Do not resolve IP addresses to their domain names -p port --port=port Set the destination port to use. It is either initial udp port value for "default" method (incremented by each probe, default is 33434), or initial seq for "icmp" (incremented as well, default from 1), or some constant destination port for other methods (with default of 80 for "tcp", 53 for "udp", etc.) -t tos --tos=tos Set the TOS (IPv4 type of service) or TC (IPv6 traffic class) value for outgoing packets -l flow_label --flowlabel=flow_label Use specified flow_label for IPv6 packets -w waittime --wait=waittime Set the number of seconds to wait for response to a probe (default is 5.0). Non-integer (float point) values allowed too -q nqueries --queries=nqueries Set the number of probes per each hop. Default is 3 -r Bypass the normal routing and send directly to a host on an attached network -s src_addr --source=src_addr Use source src_addr for outgoing packets -z sendwait --sendwait=sendwait Minimal time interval between probes (default 0). If the value is more than 10, then it specifies a number in milliseconds, else it is a number of seconds (float point values allowed too) -e --extensions Show ICMP extensions (if present), including MPLS -A --as-path-lookups Perform AS path lookups in routing registries and print results directly after the corresponding addresses -M name --module=name Use specified module (either builtin or external) for traceroute operations. Most methods have their shortcuts (`-I' means `-M icmp' etc.) -O OPTS,... --options=OPTS,... Use module-specific option OPTS for the traceroute module. Several OPTS allowed, separated by comma. If OPTS is "help", print info about available options --sport=num Use source port num for outgoing packets. Implies `-N 1' -U --udp Use UDP to particular port for tracerouting (instead of increasing the port per each probe), default port is 53 -UL Use UDPLITE for tracerouting (default dest port is 53) -P prot --protocol=prot Use raw packet of protocol prot for tracerouting --mtu Discover MTU along the path being traced. Implies `-F -N 1' --back Guess the number of hops in the backward path and print if it differs -V --version Print version info and exit --help Read this help and exit Arguments: + host The host to traceroute to packetlen The full packet length (default is the length of an IP header plus 40). Can be ignored or increased to a minimal allowed value